Effects of acrylic acid-grafted HDPE in HDPE-based binder on properties after injection and debinding in metal injection molding

Wongpanit Panya; Khanthsri Sutthahatai; Puengboonsri SuchanyaManonukul Anchalee

首页> 外文期刊>Materials Chemistry and Physics >Effects of acrylic acid-grafted HDPE in HDPE-based binder on properties after injection and debinding in metal injection molding

【24h】

Effects of acrylic acid-grafted HDPE in HDPE-based binder on properties after injection and debinding in metal injection molding

机译：Effects of acrylic acid-grafted HDPE in HDPE-based binder on properties after injection and debinding in metal injection molding

获取原文

获取原文并翻译 | 示例

掌桥外文数据库（机构版） >>

开具论文收录证明 >>

文献代查 >>

页面导航

摘要
著录项
相关主题

摘要

The objective of the present work is to investigate the effects of acrylic-acid grafted high density polyethylene (AAHDPE) content in a HDPE-based binder (at 0 vol, 5 vol, 10 vol and 25 vol) on physical, mechanical, and morphological characteristics of parts after injection as well as on physical properties and appearance of parts after debinding. Calculated theoretical densities of the parts after injection slightly decreased with an increase in the AAHDPE content, while the densities measured by Archimedes' principle and mass/volume measurement exhibited the opposite tendency. The cross-sectional fractured surfaces of hexane-treated injected parts indicated that the interaction between the binder and the metal powder was significantly increased when the AAHDPE content was greater than 10 vol. The fractured cross-sectional surfaces of hexane-treated injected parts further revealed the phase separation between HOPE and paraffin wax (PW). The flexural strength and flexural strain at break increased with increasing AAHDPE content in binder before reaching a plateau region, when the AAHDPE contents were 5 vol and 10 vol, respectively. After thermal debinding, the distortion of debinded parts as well as volume expansion of materials was observed. The distortion angle analysis found that the distortion angles tended to decrease remarkably with increasing AAHDPE content. The results of the present study suggest that AAHDPE is a key component in the HDPE-based binder, i.e. acting as a compatibilizer for binder/ metal powder. Consequently, mechanical properties of the parts after injection could be enhanced and in addition the distortion of the debinded parts could be reduced. (C) 2014 Elsevier B.V. All rights reserved.

著录项

来源
《Materials Chemistry and Physics》 |2014年第2期|238-246|共9页
作者
Wongpanit Panya; Khanthsri Sutthahatai; Puengboonsri SuchanyaManonukul Anchalee;
展开▼
作者单位

Srinakharinwirot Univ, Fac Agr Prod Innovat & Technol, Bangkok 10110, Thailand;

Natl Met & Mat Technol Ctr, Pathum Thani 12120, Thailand;

展开▼
收录信息美国《科学引文索引》(SCI);美国《工程索引》(EI);美国《生物学医学文摘》(MEDLINE);
原文格式 PDF
正文语种英语
中图分类工程基础科学;工程材料学;
关键词
Composite materials; Polymers; Powder metallurgy; Mechanical testing; Optical microscopy; Deformation; MIM; FEEDSTOCK; COMPOSITES; BEHAVIOR;

Effects of acrylic acid-grafted HDPE in HDPE-based binder on properties after injection and debinding in metal injection molding

摘要

著录项

相关主题

期刊订阅