• 主题
高级搜索  >
历史搜索 清空历史
首页> 外文期刊>International Journal of Computer Integrated Manufacturing >Models, guidelines and tools for the integration of collaborative processes in non-hierarchical manufacturing networks: a review
【24h】

Models, guidelines and tools for the integration of collaborative processes in non-hierarchical manufacturing networks: a review

机译：在非分层制造网络中集成协作过程的模型，指南和工具：回顾

获取原文
获取原文并翻译 | 示例
           
页面导航
  • 摘要
  • 著录项
  • 相似文献
  • 相关主题

摘要

Collaborative practices among partners of manufacturing networks require the support of models (M), guidelines (G) and tools (T) which should take into account the network topology. Most of the M, G and T proposed in the literature were developed for hierarchical manufacturing networks (HN), but most of the real manufacturing networks, mainly composed by small-sized enterprises, are in fact non-hierarchical manufacturing networks (NHN). This paper focuses its research on the collaborative processes in NHN and its specific needs to be supported by M, G and T. Firstly, a literature review is conducted, allowing identifying a set of relevant collaborative processes in manufacturing networks (both HN and NHN), as well as the M, G and T designed to address each of them. Secondly, an analysis is carried out in order to determine how these M, G and T, designed for HN and/or NHN, adjust to the needs of the NHN. The assessment carried out reveals that some of the proposed M, G and T do not entirely fill the requirements demanded in NHN contexts. Each collaborative process is classified into a satisfactory, acceptable or unacceptable degree of coverage, depending on the extent into which the provided M, G and T can be applied in NHN. On this basis, it is concluded that some of the identified collaborative processes have a clear lack on the M, G and T for its proper application in NHN. Finally, potential future research lines are suggested in terms of providing solution approaches, missing in the literature, to adequately support the collaborative processes in NHN contexts.
机译：制造网络合作伙伴之间的协作实践需要模型（M），准则（G）和工具（T）的支持，这些模型应考虑网络拓扑。文献中提出的大多数M，G和T都是为分层制造网络（HN）开发的，但实际上，主要由小型企业组成的大多数实际制造网络实际上是非分层制造网络（NHN）。本文将重点放在NHN的协作过程及其由M，G和T支持的特定需求方面的研究。首先，进行文献综述，从而确定制造网络（HN和NHN）中的一组相关协作过程。 ，以及分别针对它们的M，G和T。其次，进行分析以确定这些为HN和/或NHN设计的M，G和T如何适应NHN的需求。进行的评估表明，某些拟议的M，G和T不能完全满足NHN上下文中的要求。根据提供的M，G和T可以在NHN中应用的程度，将每个协作过程分为满意，可接受或不可接受的覆盖程度。在此基础上，得出的结论是，某些已确定的协作过程明显缺乏M，G和T，无法在NHN中正确使用。最后，从提供文献中缺少的解决方法的角度，提出了潜在的未来研究方向，以充分支持NHN上下文中的协作过程。

著录项

相似文献

  • 外文文献
  • 中文文献
  • 专利
获取原文

客服邮箱：kefu@zhangqiaokeyan.com

京公网安备：11010802029741号 ICP备案号：京ICP备15016152号-6 六维联合信息科技 (北京) 有限公司©版权所有

  • 客服微信

  • 服务号