...
  • 主题
高级搜索  >
历史搜索 清空历史
首页> 外文期刊>Odontology >Surface substance loss of subsurface bovine enamel lesions after different steps of the resinous infiltration technique: A 3D topography analysis
【24h】

Surface substance loss of subsurface bovine enamel lesions after different steps of the resinous infiltration technique: A 3D topography analysis

机译：在树脂渗透技术的不同步骤后，地下牛牙釉质病变的表面物质损失：3D地形分析

获取原文
获取原文并翻译 | 示例
           
页面导航
  • 摘要
  • 著录项
  • 相似文献
  • 相关主题

摘要

Surface substance loss of subsurface enamel lesions before (baseline/demineralization) and after each step of the infiltration technique was evaluated by means of a three-dimensional focus variation. Eighty enamel specimens were prepared and partially varnished (control). Non-varnished areas were demineralized (pH 4.95; 28 days), and etched with phosphoric acid gel (20%; 5 s). Specimens were randomly assigned to eight groups (n = 10), and were infiltrated using four resinous materials. In subgroups 1, polymerization and finishing with abrasive polishing strips followed. In subgroups 2, excess material was removed before polymerization (E1/E2-Excite, Vivadent; F1/F2-Fortify, Bisco; G1/G2-Glaze & Bond, DMG; I1/I2-Icon, DMG). Topometrical evaluation revealed a negligible substance loss of demineralized enamel. After etching, mean (±SD) differences of height decreased uniformly (-6.6 ± 2.0 μm; p = 0.089; ANOVA). For infiltrated lesions, DH of subgroups 1 was comparable to the etched lesions, with a significant increase (compared to etched lesions) in subgroups 2 (1.1 ± 0.1 μm; p < 0.001; t test). Within the limitations of this study, it is concluded that etching of initial subsurface lesions will result in significant surface substance loss; removal of excess material before light-curing should simplify the infiltration procedure, and this will avoid any abrasion resulting from polishing procedures.
机译：通过三维聚焦变化评估在浸润技术的每个步骤之前（基线/去矿质化）和之后的地下釉质病变的表面物质损失。制备了80个搪瓷样品并进行了部分清漆（对照）。使未上漆的区域脱盐（pH 4.95; 28天），并用磷酸凝胶蚀刻（20％; 5 s）。将标本随机分为8组（n = 10），并用4种树脂材料浸润。在第1组中，进行聚合并用磨料抛光条进行精加工。在子组2中，在聚合之前除去了多余的材料（E1 / E2-Excite，Vivadent; F1 / F2-Fortify，Bisco; G1 / G2-Glaze＆Bond，DMG; I1 / I2-Icon，DMG）。拓扑学评估显示，脱矿质搪瓷的物质损失可忽略不计。蚀刻后，平均高度差异（±SD）均匀降低（-6.6±2.0μm; p = 0.089; ANOVA）。对于浸润性病变，第1组的DH与蚀刻的病变相当，在第2组中（与蚀刻的病变相比）显着增加（1.1±0.1μm; p <0.001; t检验）。在本研究的范围内，得出的结论是，蚀刻最初的表面下的病变将导致明显的表面物质损失。在光固化之前去除多余的材料应简化渗透过程，这将避免抛光过程造成的任何磨损。

著录项

相似文献

  • 外文文献
  • 中文文献
获取原文

客服邮箱：kefu@zhangqiaokeyan.com

京公网安备：11010802029741号 ICP备案号：京ICP备15016152号-6 六维联合信息科技 (北京) 有限公司©版权所有

  • 客服微信

  • 服务号