Building a better tube bend-ing en-cy-clo-pe-di-a/PART II: D through H

William Q. Tingley III

首页> 外文期刊>The tube & pipe journal >Building a better tube bend-ing en-cy-clo-pe-di-a/PART II: D through H

【24h】

Building a better tube bend-ing en-cy-clo-pe-di-a/PART II: D through H

机译：建立更好的弯管en-cy-clo-pe-di-a / PART II：D到H

获取原文

获取原文并翻译 | 示例

掌桥外文数据库（机构版） >>

开具论文收录证明 >>

文献代查 >>

页面导航

摘要
著录项
相似文献
相关主题

摘要

D-A unit of radial measurement peculiar to tube bending. D is the ratio of the centerline radius to the nominal, not the true, outside diameter of the material: D=CLRominal TOD. This distinction between nominal and true diameters is critical when D of bend specifies the centerline radius of a pipe-as opposed to a tube-bend, because pipe diameters by definition are nominal values. For example, the centerline radius of a 3D bend of a 2-inch international pipe size (IPS) pipe (which has a 2.375-in. true diameter) is 6 in. instead of 7.125 in. Degree of Bend-The depth of bend; the sweep of the arc. The minimum degree of bend is about 5 degrees; the maximum degree of bend in rotary draw bending is 180 degrees.

机译：D-A弯管特有的径向测量单位。 D是中心线半径与材料的标称外径（不是真实的外径）的比率：D = CLR /标称TOD。当弯曲的D指定管的中心线半径而不是管的弯曲时，名义直径与真实直径之间的区别至关重要，因为根据定义，管道直径是名义值。例如，2英寸国际管道尺寸（IPS）管道（真实直径为2.375英寸）的3D弯曲的中心线半径为6英寸，而不是7.125英寸。弯曲度-弯曲深度;弧线的扫掠。最小弯曲度约为5度;旋转拉伸弯曲的最大弯曲度为180度。

著录项

来源
《The tube & pipe journal》 |2002年第8期|共4页
作者
William Q. Tingley III;
展开▼
作者单位

展开▼
收录信息
原文格式 PDF
正文语种 eng
中图分类管道运输;金属压力加工;
关键词

相似文献

外文文献
中文文献
专利

1. Building a better tube bend-ing en-cy-clo-pe-di-a/PART II: D through H [J] . William Q. Tingley III The tube & pipe journal . 2002,第8期

机译：建立更好的弯管en-cy-clo-pe-di-a / PART II：D到H
2. Building a better tube bend-ing en-cy-clo-pe-di-a [J] . William Q. Tingley III The tube & pipe journal . 2003,第5期

机译：构建更好的弯管en-cy-clo-pe-di-a
3. Building a better tube bend-ing en-cy-clo-pe-di-a [J] . William Q. Tingley III The tube & pipe journal . 2002,第7期

机译：构建更好的弯管en-cy-clo-pe-di-a
4. Study on the Manufacture Technolog of the Zirconia Tubes III. Research on the Slip Casting Process of the Zirconia Tubes [C] . Suntai Qiu, Jiayin Xu, Changgui Shao Conference on Solid Tate Ionics Materials and Devices Fuzhou, China 29 October -4 November 2000 . 2000

机译：氧化锆管的制造技术研究III。氧化锆管的滑模铸造工艺研究
5. The creeping motion of immiscible drops through a converging/diverging tube: I. Non-Newtonian effects of viscoelastic drops. II. Effects of constant pressure gradient condition for the flow. III. Motion of drops through a parallel channel. [D] . Avila-Segura, Francisco E. 1988

机译：不混溶液滴通过会聚/发散管的蠕变运动：I.粘弹性液滴的非牛顿效应。二。恒定压力梯度条件对流动的影响。三，液滴通过平行通道运动。
6. The microsporidian spore invasion tube. III. Tube extrusion and assembly [O] . 1982

机译：微孢子虫孢子入侵管。三管材挤出和组装
7. Construction Sequence Analysis of Tube in Tube Structural System Building [O] . 2020

机译：管结构系统建筑管施工序列分析
8. The General Plane Stress Failure of Boron Aluminum Composites. Part II. Phase I:Theoretical Analysis of Cylindrical Tubes for Characterization of Boron/Aluminum Composites. Phase II:Plasticity and Combined Loading Analysis of Cylindrical Tubes for Characterization of Boron/Aluminum Composites. [R] . vicario, a. a. freeman, w. t. 1974

机译：硼铝复合材料的一般平面应力破坏。第二部分。第一阶段：用于表征硼/铝复合材料的圆柱管的理论分析。第二阶段：用于表征硼/铝复合材料的圆柱管的塑性和组合载荷分析。

Building a better tube bend-ing en-cy-clo-pe-di-a/PART II: D through H

摘要

著录项

相似文献

相关主题

期刊订阅